— Blogs —
—Products—
Consumer hotline +8618073152920 WhatsApp:+8615367865107
Address:Room 102, District D, Houhu Industrial Park, Yuelu District, Changsha City, Hunan Province, China
Product knowledge
Time:2026-08-17 09:03:00 Popularity:261
Quick answer: A temperature and humidity sensor that repeatedly raises and clears an alarm needs a measurement check and a control-logic check. Preserve the unfiltered readings, timestamps and alarm transitions before changing settings. Small displayed steps do not establish the instrument's accuracy, and a large delay can hide a real event. NiuBoL field sensors provide measurement channels; alarm hysteresis, delays and equipment actions belong to the receiving controller unless explicitly included.
The cup anemometer below is a separate wind-speed instrument. Its signal must not be mapped to a temperature or RH alarm simply because the weather station shares one cabinet.

Capture a short record around several transitions. Include temperature, relative humidity, raw received values, decoded engineering values, acquisition time and the controller's alarm state. Add relevant fan, vent, heater or misting commands. This makes it possible to distinguish a real operating cycle from a decoding error or repeated use of stale data.
Compare the sensor location with the condition the alarm is meant to represent. A probe next to a mist outlet or warm panel may track a real local change that does not represent the managed space. Correct the measurement location or airflow problem before adding software filtering. If there is condensation or contamination at the sensing area, investigate that condition using the applicable service procedure.
The THPLC assembly below supplies temperature and RH alongside pressure, illuminance and CO2. Those extra channels do not improve its stated RH accuracy or establish a built-in ventilation-control sequence.

| Item | NBL-W-51MUWS | NBL-W-THPLC |
|---|---|---|
| Temperature channel | -50 to 100 C; +/-0.5 C; resolution 0.1 C | -50 to 100 C; +/-0.5 C; resolution 0.1 C |
| RH channel | 0-100% RH; +/-5% RH; resolution 0.1% RH | 0-100% RH; +/-5% RH; resolution 0.1% RH |
| Assembly operating conditions | -40 to 80 C; 0-95% RH | -50 to 80 C; 0-100% RH |
| Supply | 12-24 VDC | 12 VDC or 24 VDC version |
| Interface | RS485 Modbus RTU; 9600 bps | RS485; confirm the ordered protocol |
| Power / protection | Approximately 0.3 W; IP65 | Confirm for the supplied assembly |
| Cable | Standard 2.5 m; confirm jacket material | Confirm length and jacket material |
A 0.1% RH display step does not mean changes of that size are accurate. The +/-5% RH specification also does not tell the engineer what deadband to use: measurement uncertainty, short-term variation and the process's permitted operating band are different quantities. Assess whether the sensor's accuracy fits the actual decision before adjusting alarm logic.
The 51MUWS shown below is a multi-parameter field assembly, not a direct replacement for every indoor controller probe. Check the receiving interface and operating limits independently of the alarm settings.

Hysteresis separates the entry and clearing thresholds. As an illustrative controller test, an alarm might enter at 80% RH and clear below 75% RH. Those numbers are not recommended settings for a crop, building or process. The responsible engineer must choose the permitted band and verify that it remains useful given the measurement uncertainty.
A persistence delay asks how long a condition must remain present before a state changes. Define whether it applies to entry, clearing or both. Filtering changes the reported trend, while hysteresis changes state transitions; do not treat them as interchangeable remedies. Preserve enough raw information to show what the chosen logic has suppressed or delayed.
For RS485 Modbus RTU, verify the correct RH register, scale and unit. The 51MUWS communication interval must be at least 1000 ms; faster polling does not prove a faster physical response. For a THPLC connection, obtain the actual protocol before configuring the receiver. Treat communication loss as a separate quality state rather than a low-humidity reading.
The six-parameter weather sensor below also includes rainfall. Its rain and wind signals remain separate from the temperature/RH state being evaluated.

No. It can arise from actual local cycling, unsuitable placement, decoding, data age or controller settings. Compare the measurement and alarm records before changing calibration or ordering a replacement.
No. Display resolution, accuracy and observed short-term variation are different. Select the alarm band from the process requirement and verified installed measurement, not the number of decimal places.
No. A delay can conceal a genuine event. Test the acceptable response time and retain the underlying trend so operators can see what happened before the alarm changed state.
Do not assume that function. Confirm the controller, actuator interface and approved sequence separately. RS485 measurement output is not itself a power-switching output.
Send the model, location photographs, receiver settings, raw and decoded data, timestamps and a record of alarm transitions with equipment commands. These details help NiuBoL distinguish measurement selection from a controller or installation issue.

Resolve alarm chatter by checking the installed reading and the state logic separately. Confirm that the instrument fits the required tolerance, correct location or data faults, then verify hysteresis and delays against the operating response the site actually needs.
Prev:Smart Soil Moisture Meter: Recheck Irrigation Thresholds After Replanting
Next:Water Turbidity Meter for Intermittent Discharge: Capture Each Release
Related recommendations
Sensors & Weather Stations Catalog
Agriculture Sensors and Weather Stations Catalog-NiuBoL.pdf
Weather Stations Catalog-NiuBoL.pdf
Agriculture Sensors Catalog-NiuBoL.pdf
Water Quality Sensor Catalog-NiuBoL.pdf
Related products
Combined air temperature and relative humidity sensor
TDR Soil Moisture & Temperature Sensor for irrigation| RS485 |4-20mA| NBL-S-THR
Soil pH sensor RS485 soil Testing instrument soil ph meter for agriculture |NBL-S-PH
Wind Speed sensor Output Modbus/RS485/Analog/0-5V/4-20mA
Tipping bucket rain gauge for weather monitoring auto rainfall sensor RS485/Outdoor/stainless steel
Pyranometer Solar Radiation Sensor 4-20mA/RS485
Screenshot, WhatsApp to identify the QR code
WhatsApp number:+8615367865107
(Click on WhatsApp to copy and add friends)