— Blogs —
—Products—
Consumer hotline +8618073152920 WhatsApp:+8615367865107
Address:Room 102, District D, Houhu Industrial Park, Yuelu District, Changsha City, Hunan Province, China
Product knowledge
Time:2025-09-07 11:01:28 Popularity:1535
Digital humidity and temperature meters should be selected around the measurement location and the action taken from the result. A wall-mounted transmitter, an outdoor shielded sensor and a handheld reference instrument have different roles. Check actual accuracy, exposure, output and recording requirements before treating a display or a digital interface as proof of suitability.

A meter provides a reading for an operator. A transmitter supplies a signal to another device. A recorder stores observations with a time reference. One assembly may combine these functions, but they are not implied by the words temperature and humidity sensor. A local display does not establish that historical records can be exported.
For warehouse monitoring, a fixed transmitter feeding a building controller may be sufficient. For a temporary investigation, a portable instrument may be easier to move between locations. For outdoor weather observations, radiation shielding and ventilation matter as much as the electronic specification. Start with the intended observation, then specify the functions needed to use it.
There is no universal requirement that every professional instrument must achieve +/-0.2 degree C and +/-1% RH. A project with a narrow allowable environmental band may need tighter performance than a general greenhouse observation. Establish the allowable measurement error from the process requirement, including installation and reference uncertainty, rather than copying a generic accuracy recommendation.
Relative humidity accuracy expressed in % RH is not the same as a percentage of the displayed value. Resolution is also different from accuracy. A display with 0.1% RH increments does not establish accuracy of +/-0.1% RH. Check the specified conditions and whether the required performance applies across the operating region that matters to the project.

| Selection point | Wall-mounted temperature/humidity transmitter | NBL-W-LBTH shielded air sensor |
|---|---|---|
| Typical measurement location | Indoor air monitoring in warehouses, rooms and greenhouses | Ambient air observations with a louvered radiation shield |
| Temperature measurement range | -50 to 100 degree C | -40 to 80 degree C |
| Temperature accuracy and resolution | +/-0.5 degree C; 0.1 degree C resolution | +/-0.5 degree C; 0.1 degree C resolution |
| Humidity range and accuracy | 0-100% RH; +/-5% RH | 0-100% RH; +/-5% RH |
| Supply and output selection | 12 V or 24 V DC; voltage, 4-20 mA or RS485 versions | 12-24 V DC; 4-20 mA or RS485 Modbus RTU versions |
| Important limitation | Measurement range alone does not define the allowable housing exposure | The shield needs airflow and suitable separation from local heat sources |
The wall-mounted transmitter and NBL-W-LBTH are examples, not interchangeable indoor and outdoor packages. Order the actual output version. Where a process needs +/-1% RH, the listed +/-5% RH specification does not meet that requirement merely because a finer value is displayed.
A warehouse wall near a loading door experiences different conditions from the center of a rack aisle. In a greenhouse, a sensor beside a misting nozzle may remain locally wet while most of the crop zone is drier. Record the reason for each location and place additional points where the decision depends on a separate zone.
For outdoor air measurements, keep the shield away from exhausts, sun-heated surfaces and enclosed corners. Do not expose an indoor wall transmitter to direct sun simply because its measurement range includes high temperatures. The upper temperature range of an element is not a radiation shield specification.

A monitoring installation may also include particulate matter measurements, as illustrated above. PM2.5 and PM10 are separate channels, not functions provided by an ordinary humidity transmitter. Include them only when the project needs those measurements, and retain their own units and maintenance requirements.
RS485 is the electrical interface; Modbus RTU is the communication protocol. Confirm the protocol for the ordered model rather than assuming every RS485 product uses the same messages. The PLC, RTU or data logger needs the address, serial settings, register definitions, scaling and representation of negative temperatures.
For a 4-20 mA version, identify the assigned lower and upper engineering values for each channel. Verify whether separate outputs are provided for temperature and humidity and whether the receiving input is correctly configured. Do not apply one conversion formula to every transmitter without checking its selected range.
Then define the record: channel location, unit, timestamp, observation interval and missing-data behavior. A networked sensor does not necessarily contain storage, cloud access or an alarm relay. Those functions may belong to the logger or controller and must be included in the system scope.

Humidity measurements depend on the air reaching the sensing element. A filter, stagnant location or protective cover can change the time needed to follow a room change. Let a comparison instrument and the installed sensor stabilize in comparable conditions before judging the difference between them.
Near condensation, a wetted element may require recovery time. A 0-100% RH measurement range should not be interpreted as a blanket promise of accurate operation during liquid-water exposure. Describe washdown, mist, dust and chemical vapors in the inquiry so the housing, filter and installation can be reviewed for those conditions.
A calibration determines the relationship between readings and reference values under defined conditions. Adjustment changes the response. Do not change the sensor or controller offset merely to make two readings agree before investigating location, stabilization and reference uncertainty. Keep the original comparison results when an adjustment is made.
If the project requires a calibration report, specify the temperature and humidity points, identification and uncertainty information needed. Certificate availability, scope and any accredited service should be established for the ordered configuration; they are not automatic consequences of buying a digital sensor.
A complete environmental system may combine air sensors, separate weather measurements and a logger. The diagram below illustrates these different components. Select only the measurements and recording functions required for the project, and keep their specifications separate when preparing the equipment list.

The following downloads cover air sensors and a separate particulate sensor. Check the model and channel set separately; a particulate-sensor document does not extend the functions of a temperature and humidity transmitter.
NBL-W-LBTH-Atmosphere-temperature-humidity-and-pressure-sensor-instruction-manual-V4.0.pdf
NBL-W-WHTP-Wall-Mounted-Temperature-Humidity-and-Pressure-Sensors.pdf
NBL-W-PM25-PM10-Integrated-sensors-Manual.pdf
No. The stated performance does not meet that requirement. Select an instrument with documented performance that meets the requirement or review the actual process tolerance. Extra decimal places, averaging and a local display do not turn the listed accuracy into +/-1% RH.
It supplies environmental measurements, but the project still needs a recording function if historical data is required. Define the logger, storage interval and export method separately, along with the sensor location and selected interface.
Only with suitable exposure and stabilization. A handheld instrument warmed by the operator or exposed to sunlight may not represent the air inside the installed shield. A difference under unmatched conditions is not enough to diagnose calibration error.
No. They require different receiving hardware and data handling. For fixed controller integration, confirm the actual protocol and register map. For portable recording, confirm file access, timestamps and whether the required history is stored locally.
Send the normal and extreme conditions, allowable error, installation location, number of points, controller inputs and required records. Identify condensation or cleaning exposure and any calibration documentation requirement. NiuBoL can then review a configuration against the task rather than an unspecified professional-use label.
Select digital humidity and temperature meters by the required decision, measurement location and data function. Check accuracy against the process tolerance, allow representative airflow, and specify recording and communications explicitly. A configuration that meets those conditions is more useful than an unsupported claim of universal precision or automatic certification.
Prev:Agriculture Sensor Certifications: Review Model and Document Scope
Next:Weather Station Buying Mistakes: Five Checks Before Order Approval
Related recommendations
Sensors & Weather Stations Catalog
Agriculture Sensors and Weather Stations Catalog-NiuBoL.pdf
Weather Stations Catalog-NiuBoL.pdf
Agriculture Sensors Catalog-NiuBoL.pdf
Water Quality Sensor Catalog-NiuBoL.pdf
Related products
Combined air temperature and relative humidity sensor
TDR Soil Moisture & Temperature Sensor for irrigation| RS485 |4-20mA| NBL-S-THR
Soil pH sensor RS485 soil Testing instrument soil ph meter for agriculture |NBL-S-PH
Wind Speed sensor Output Modbus/RS485/Analog/0-5V/4-20mA
Tipping bucket rain gauge for weather monitoring auto rainfall sensor RS485/Outdoor/stainless steel
Pyranometer Solar Radiation Sensor 4-20mA/RS485
Screenshot, WhatsApp to identify the QR code
WhatsApp number:+8615367865107
(Click on WhatsApp to copy and add friends)