Call Phone +8618073152920 Hotline: +8618073152920
Call Phone +8618073152920
English
CONTACT US/ CONTACT US
Consumer hotline +8618073152920
Changsha Zoko Link Technology Co., Ltd.

Email:Arvin@niubol.com

WhatsApp:+8615367865107

Address:Room 102, District D, Houhu Industrial Park, Yuelu District, Changsha City, Hunan Province, China

Position:Home >> Blogs >> Product knowledge

Product knowledge

CO2 Temperature Humidity Sensor Placement: Measure Representative Crop Air

Time:2026-08-18 09:04:00 Popularity:316

A CO2 temperature humidity sensor should measure the air the operator intends to manage, not a concentrated plume from a dosing tube, an open door or a wet surface. Combining channels in one enclosure is useful only when one location suits their common purpose. For greenhouse climate monitoring, evaluate the measurement position before using the readings to change ventilation or CO2 supply.

NBL-W-THPLC integrated CO2 temperature humidity pressure and illuminance sensor

Decide whether one location represents the crop air

The NiuBoL NBL-W-THPLC combines temperature, relative humidity, pressure, illuminance and CO2. It can collect related environmental observations at one point. That point still needs to represent the greenhouse zone: a sensor close to a CO2 outlet can record local enrichment while a nearby vent samples a different air mixture.

Review the position relative to the crop canopy as it develops, fan flow, vents, doors, heating and fogging. Where these influences cannot be avoided at one location, compare separate climate points rather than assuming a single integrated body describes the whole structure. There is no universal mounting height for every crop and greenhouse geometry.

CO2 temperature humidity sensor limits for the proposed location

THPLC channel or interfaceSpecificationSelection consequence
CO20-2000 ppm; accuracy +/-(40 ppm + 2% FS); 1 ppm resolutionOver this span, the stated expression gives +/-80 ppm. Do not confuse 1 ppm display resolution with accuracy.
Relative humidity0-100% RH; accuracy +/-5% RH; 0.1% RH resolutionCheck whether the error allowance suits the operating decision. A wide range alone does not establish resistance to direct spray.
TemperatureChannel range -50 to 100 degrees C; accuracy +/-0.5 degrees CThe assembly operating range is -50 to 80 degrees C. Do not use the higher channel endpoint as its ambient limit.
Supply12 V DC or 24 V DC optionIdentify the ordered supply version rather than treating the two options as a continuous input range.
OutputRS485Obtain the delivered protocol, serial settings and data map before integrating with a PLC, RTU or data logger.

If the required CO2 operating or alarm range exceeds 2000 ppm, select a different suitable configuration rather than clipping the value in the software. Request confirmation of enclosure protection, condensation tolerance, cable and power requirements where these are decisive; do not infer them from the appearance of a radiation shield.

Keep outdoor weather and indoor climate observations separate

A separate outdoor weather point can provide wind and rain context for greenhouse operation. The six-parameter ultrasonic assembly below measures weather variables; it is not the THPLC CO2 instrument. Assign different point names so an outside RH reading cannot replace the inside crop-zone value in a dashboard or control rule.

61MUWS outdoor ultrasonic weather assembly for a separate weather point

Inside the greenhouse, screen candidate positions during normal operation. Place a suitable comparison instrument alongside the installed sensor, allow appropriate stabilization and record conditions with ventilation, fans and CO2 dosing in their usual states. Then compare a second position at the same time where possible. A disagreement between separated points may be a real gradient rather than calibration drift.

Record the location and height of each observation. Moving the sensor from a vent to the canopy changes the observation, even if the address and dashboard label remain unchanged. Mark that change in the trend record so a new baseline is not mistaken for a sudden improvement in climate control.

71GUWS integrated weather instrument requiring its own outdoor point identity

Investigate a local plume before changing calibration

If CO2 rises when dosing starts but differs substantially between nearby positions, inspect the distribution route and airflow first. If RH rises immediately after misting, check for direct wetting or a location dominated by the mist path. A combined instrument cannot correct a nonrepresentative location through a single calibration adjustment.

Keep the temperature, RH and CO2 values separate in storage. Preserve their units and distinguish a missing channel from a valid extreme. Before calculating a derived climate indicator, check that the input temperature and RH came from the same intended observation period and location.

Outdoor particulate and noise monitoring may use a separate eight-parameter assembly. That is a different channel combination from an indoor CO2 temperature humidity sensor. Additional measurements justify their cost only when they answer a separate site question.

81GUWS weather and environmental assembly for separate particulate or noise observations

Check the receiving system without assuming a protocol

RS485 describes the electrical interface; it does not by itself establish Modbus RTU. If the host requires RS485 Modbus RTU, make that a procurement condition and obtain the exact supported protocol and register map for the supplied THPLC. Do not copy the protocol from an integrated weather station into this product's specification.

Verify each channel against the field instrument or suitable reference, then check units, scale and missing-data behavior in the host. Record ventilator and CO2-supply events on the same time basis when the platform supports them. A chronological association helps investigation, but it does not prove that one channel caused the change in another.

A ten-parameter outdoor weather assembly can add rain, particulate or solar/light observations for site context. It does not remove the need for a representative indoor CO2 point. Specify the inside and outside channel lists separately.

10GUWS outdoor weather assembly, distinct from the THPLC CO2 instrument

Project Decision FAQ

Q1. Should the CO2 temperature humidity sensor be beside the CO2 outlet?

Not when the purpose is to represent mixed crop-zone air. An outlet position may be useful for diagnosing distribution, but it can be unsuitable as the sole control observation. Compare candidate positions while the system operates normally.

Q2. Can one sensor cover several greenhouse bays?

Only after site observations show that the bays are sufficiently comparable for the decision. Different ventilation, crops and dosing layouts can require separate points. Adding channels to one enclosure does not increase spatial coverage.

Q3. Does the THPLC offer a 5000 ppm CO2 range?

The THPLC CO2 range is 0-2000 ppm. If the project requires 5000 ppm or another range, obtain a specific suitable model or configuration and its accuracy statement before ordering. Do not assume the same unit can be extended by software.

Q4. Can this replace a personnel CO2 safety detector?

Do not treat an environmental monitoring sensor as a safety detector without the necessary range, alarm functions and project approvals. State any personnel-protection duty separately for review by the responsible safety engineer.

Q5. What information makes the quotation useful?

Provide greenhouse layout, crop and canopy range, ventilation and dosing positions, required CO2 range, host protocol and supply. Include spray or condensation exposure so the proposed installation and protection can be assessed before purchase.

Configurable ultrasonic weather assembly for independent outside observations

Summary

Select a CO2 temperature humidity sensor around the observation it must represent. Verify placement, CO2 span and the actual receiving interface before enabling control. Send NiuBoL the greenhouse layout and inside/outside channel requirements to review whether THPLC or separate measurement points fit the project.

Related recommendations

Sensors & Weather Stations Catalog

Agriculture Sensors and Weather Stations Catalog-NiuBoL.pdf

Weather Stations Catalog-NiuBoL.pdf

Agriculture Sensors Catalog-NiuBoL.pdf

Water Quality Sensor Catalog-NiuBoL.pdf

Related products

Tell us your requirements, Let's discuss more about your project.we can do more.

Name*

Tel*

Email*

Company*

Country*

Message


online
Contacts
Email
Top
XCO2 Temperature Humidity Sensor Placement: Measure Representative Crop Air-Product knowledge-Automatic Weather Stations_Industrial, Agricultural, Water & Environmental IoT Monitoring Solutions—NiuBoL

Screenshot, WhatsApp to identify the QR code

WhatsApp number:+8615367865107

(Click on WhatsApp to copy and add friends)

Open WhatsApp

The WhatsApp ID has been copied, please open WhatsApp to add consultation details!
WhatsApp