Call Phone +8618073152920 Hotline: +8618073152920
Call Phone +8618073152920
English
CONTACT US/ CONTACT US
Consumer hotline +8618073152920
Changsha Zoko Link Technology Co., Ltd.

Email:Arvin@niubol.com

WhatsApp:+8615367865107

Address:Room 102, District D, Houhu Industrial Park, Yuelu District, Changsha City, Hunan Province, China

Position:Home >> Blogs >> Product knowledge

Product knowledge

Anemometer for Greenhouse Ventilation: Exposure and Fault Response

Time:2026-08-19 09:02:00 Popularity:318

An anemometer for greenhouse ventilation should observe the outside wind exposure that matters to the vents, then deliver that observation to the local controller with a clear validity state. An inside circulation-fan reading describes a different airflow. Specify the measurement location and the vent manufacturer's operating requirements before selecting a sensor or setting a wind threshold.

NBL-W-61MUWS outdoor ultrasonic weather sensor with wind direction and rain channels

Start with the vent arrangement and surrounding structures

Identify the roof or side vents, their opening directions and any nearby buildings, trees or greenhouse blocks that shelter or disturb the airflow. A sheltered mounting point can report modest wind while another roof section is more exposed. Conversely, a roof edge may create a local flow pattern that does not represent the intended observation.

The mounting review should establish what one wind point can reasonably represent. Large or differently exposed greenhouse blocks may need separate points or a documented conservative control strategy. More measurement channels in one assembly do not expand its geographical coverage.

Choose an anemometer for greenhouse ventilation by the required inputs

The NiuBoL NBL-W-61MUWS combines ultrasonic wind speed and direction with temperature, humidity, pressure and piezoelectric rainfall. A compatible PLC, RTU or data logger can receive its RS485 Modbus RTU data. The sensor provides observations; the receiving controller must implement any vent movement, alarm and fault response.

Selection itemNBL-W-61MUWSNBL-W-10GUWS alternative
Wind-speed range and accuracy0-40 m/s; +/-(0.5 m/s + 2% FS)0-60 m/s; +/-(0.3 m/s + 3% FS)
Wind direction0-359 degrees; +/-3 degrees0-359 degrees; +/-3 degrees
Power and output12-24 V DC; approximately 0.35 W; RS485 Modbus RTU9-24 V DC; approximately 1 W with PM sensor; RS485 Modbus RTU
Assembly operating limits-20 to 50 degrees C; 0-95% RH; IP65-40 to 80 degrees C; 0-95% RH; IP65
Additional observationsTemperature, RH, pressure and rainTemperature, RH, pressure, rain, PM2.5, PM10, noise and solar radiation or illuminance

A wider wind span does not automatically mean smaller error near a vent-control threshold. At the listed full scales, the stated expressions give +/-1.3 m/s for 61MUWS and +/-2.1 m/s for 10GUWS. Check whether that performance suits the required decision rather than choosing by maximum wind speed alone. Also distinguish temperature measurement range from assembly operating limits; the 61MUWS assembly is limited to -20 to 50 degrees C even though its temperature channel has a wider listed range.

NBL-W-71GUWS integrated weather sensor requiring a defined outside measurement point

Use direction only after verifying the reference

If the greenhouse controller uses different rules for windward and leeward vents, confirm the sensor orientation and direction convention at installation. Record whether the supplied output represents the direction the wind comes from and verify the host interprets it correctly. A direction offset can assign the wrong vent group even when the wind-speed number is valid.

During supervised commissioning, exercise known direction sectors using the equipment's approved test method or a suitable comparison. Check the receiving sector labels and the corresponding controller request without allowing unsafe movement. A diagram on the dashboard is not proof that the physical north reference is correct.

For farms also monitoring dust or environmental noise, an eight-parameter weather assembly may answer that separate requirement. Those extra channels should not be purchased as substitutes for validating the direction-to-vent mapping.

NBL-W-81GUWS weather assembly for separate particulate and noise observations

Specify response timing with the greenhouse controls supplier

The measured wind value, controller polling, filtering and motor travel each contribute to the time before a vent reaches its requested position. Obtain the delivered sensor's update and averaging behavior. Do not equate a fast Modbus poll with a newly measured gust or assume every integrated assembly reports the same wind statistic.

Set the permitted vent positions and response thresholds with the greenhouse and actuator suppliers. This article supplies no universal wind speed at which every structure should close. Structural design, vent geometry and operating conditions differ. An environmental sensor alone is not a certified protective system.

Rain can be a separate input to the control sequence. The 61MUWS includes a piezoelectric rainfall channel, but the controller still needs to interpret the selected output and its update behavior. Avoid turning an accumulated rain value into a persistent current-rainfall indication without checking how that register behaves.

NBL-W-10GUWS weather assembly with a model-specific wind accuracy expression

Test lost data before handing control to the weather input

Commission the installed point in manual or otherwise approved test mode. Compare field and host values, verify orientation, then interrupt communication safely and check how the controller identifies stale wind. Repeat a controlled power restart. The last valid calm reading must not remain indefinitely presented as a current observation.

The required fault position is a greenhouse-system decision: closing everything can create other crop or environmental risks, while leaving exposed vents open can also be unacceptable. Agree the response and manual override with the responsible designer rather than deriving it solely from the sensor's protection rating.

Keep the ultrasonic paths clear and arrange safe access for inspection. IP65 does not establish ice-free operation or a built-in heater. For freezing sites, obtain confirmation of the selected configuration's winter suitability before using it as a continuous control input.

Configurable outdoor ultrasonic weather assembly for a separately engineered greenhouse control input

Project Decision FAQ

Q1. Can an indoor anemometer control roof vents from outside wind?

Not as an equivalent observation. Indoor fans, screens and crop rows change local airflow. Use a representative outside wind point for the external exposure requirement and keep any internal airflow measurement separately identified.

Q2. Is one wind sensor sufficient for a large greenhouse site?

Only if the exposure review supports using one point for the intended blocks and control rules. Differently sheltered or oriented structures may need additional observations. Test that assumption rather than relying on the sensor's maximum range.

Q3. Does a 60 m/s model give more accurate low-speed control than a 40 m/s model?

Not necessarily. Compare each accuracy expression at the relevant speed and confirm update behavior. Range, resolution and accuracy are different specifications; a larger span does not by itself improve the decision.

Q4. Can the sensor directly drive a vent motor?

No direct motor-control function is established by its RS485 output. Use a compatible controller and appropriately rated actuator hardware. The control supplier must define travel limits, interlocks, overrides and measurement-fault behavior.

Q5. What should be sent for a configuration review?

Provide greenhouse layout, vent directions, surrounding obstacles, local temperature range, existing controller and required wind and rain inputs. Include mounting and cable routes so NiuBoL can review the weather assembly and interface without assuming a complete vent-control package.

Summary

Choose an anemometer for greenhouse ventilation as part of a defined observation and control chain. Representative exposure, correct direction mapping and tested stale-data behavior matter alongside model specifications. Retain separate responsibilities for weather sensing, greenhouse operating limits and actuator control.

Related recommendations

Sensors & Weather Stations Catalog

Agriculture Sensors and Weather Stations Catalog-NiuBoL.pdf

Weather Stations Catalog-NiuBoL.pdf

Agriculture Sensors Catalog-NiuBoL.pdf

Water Quality Sensor Catalog-NiuBoL.pdf

Related products

Tell us your requirements, Let's discuss more about your project.we can do more.

Name*

Tel*

Email*

Company*

Country*

Message


online
Contacts
Email
Top
XAnemometer for Greenhouse Ventilation: Exposure and Fault Response-Product knowledge-Automatic Weather Stations_Industrial, Agricultural, Water & Environmental IoT Monitoring Solutions—NiuBoL

Screenshot, WhatsApp to identify the QR code

WhatsApp number:+8615367865107

(Click on WhatsApp to copy and add friends)

Open WhatsApp

The WhatsApp ID has been copied, please open WhatsApp to add consultation details!
WhatsApp