Call Phone +8618073152920 Hotline: +8618073152920
Call Phone +8618073152920
English
CONTACT US/ CONTACT US
Consumer hotline +8618073152920
Changsha Zoko Link Technology Co., Ltd.

Email:Arvin@niubol.com

WhatsApp:+8615367865107

Address:Room 102, District D, Houhu Industrial Park, Yuelu District, Changsha City, Hunan Province, China

Position:Home >> Blogs >> Product knowledge

Product knowledge

Arduino Water Turbidity Sensor: Replace an Analog Module with RS485

Time:2026-08-20 09:05:00 Popularity:357

Replacing an analog module in an Arduino water turbidity sensor project with an industrial RS485 probe changes the measurement chain. Do not reuse the old voltage-to-NTU equation on a probe that already reports calibrated turbidity. The replacement must be checked as an optical measurement, an electrical interface and a new source of application data.

NBL-WQ-TS immersion turbidity probe with an optical window for NTU measurements

Remove the old conversion before comparing readings

A typical analog prototype turns an ADC count into voltage and then estimates turbidity with a fitted equation. That equation belongs to the original emitter, receiver, optical arrangement and calibration samples. It is not a transferable property of water and should not be applied to a different instrument's digital NTU value.

Trace the application from sensor input to displayed value. Identify ADC conversion, smoothing, temperature adjustments, calibration offsets and alarm limits. Remove only processing that no longer applies; retain useful logging and alarm functions after checking their units and response. Keep a record of the old and new measurement paths so an apparent improvement is not merely a change in averaging.

A pH channel may share the same enclosure or data logger, but it has a different calibration and engineering unit. Do not apply the new turbidity conversion to every input in a reused acquisition function. Label each channel by model, parameter and unit, rather than by an ambiguous variable such as waterValue.

Separate base pH probe requiring pH-specific calibration rather than NTU conversion

Match the replacement probe to the operating range

The NiuBoL NBL-WQ-TS is an immersion turbidity probe using 90-degree scattered light and an infrared LED. Select its range from the expected water and the decision threshold. A receiving board does not determine whether the optical instrument can resolve a low-level change.

ItemNBL-WQ-TS specificationReplacement check
Selected turbidity range0-20.00, 0-100.0 or 0-1000.0 NTUOrder the range required by the water; do not assume all spans switch automatically
Resolution0.01 NTU for 0-20.00; 0.1 NTU for the other listed spansResolution does not establish low-level accuracy
Accuracy terms0-20: +/-3% or +/-1.5 NTU; 0-100: +/-3% or +/-2 NTU; 0-1000: +/-5% or +/-3 NTUAgree the percentage basis and rule for the paired terms before setting an acceptance limit
Power and consumption12-24 V DC; 0.2 W at 12 VProvide a suitable probe supply; do not power it from a GPIO
OutputRS485 Modbus RTU; 4-20 mA output availableConfirm the ordered output and use its matching receiving circuit
Water limits0-50 degrees C; pressure below 0.2 MPa; IP68Check the process and external cable joints separately
Construction and installationPOM/ABS housing; 3/4 NPT; 5 m standard cable, other lengths configurableConfirm water compatibility, retrieval and cable protection

Do not turn the paired accuracy terms into an assumed reading-based or full-scale guarantee. The absolute NTU term can matter more than display resolution near a low alarm point. Request a clear acceptance criterion for the chosen range and water conditions before approving the replacement.

A separate digital pH probe illustrates why a common RS485 bus still needs model-specific handling. Its pH buffer checks cannot verify the optical turbidity channel, and replacing a pH model does not establish which turbidity registers the application should read.

PH-4S digital pH probe with an independent parameter and register map

Change the interface without exposing board pins to field wiring

For an Arduino water turbidity sensor upgrade using RS485, provide a compatible RS485 transceiver or interface and a suitable power arrangement. RS485 A/B are not direct UART or analog input pins. Select logic levels, isolation where required, shielding and surge protection for the actual board and field installation.

The official Arduino Modbus documentation distinguishes RTU communication over RS485 from TCP communication over a network. Installing a protocol library does not supply the physical transceiver, probe power or weather protection.

Read the selected probe's documented turbidity field and decode its type, scaling and unit once. If using a 4-20 mA version instead, provide an appropriately rated receiving input and verify the ordered current-to-range relationship. Neither path justifies retaining an unrelated analog module's polynomial.

Keep oxygen measurements independent when other probes join the station. A dissolved oxygen value uses its own units, compensation and checks; a successful reply from that address does not prove the turbidity path is working.

DO-4A dissolved oxygen probe for a separately validated oxygen channel

Compare in water that tests the optical measurement

First verify communication and displayed units using the delivered configuration. Then test with suitable turbidity reference material and representative process water. Use clean containers and avoid bubbles, settled material, direct optical interference and carryover between samples.

For the NBL-WQ-TS, maintain more than 5 cm clearance from side walls and more than 10 cm from the bottom. A narrow jar can invalidate a comparison even though the probe remains submerged. Allow the reading to stabilize under the applicable check procedure and keep the optical window clean.

Run comparison points around the intended operating threshold, not just at visibly clear and visibly dirty extremes. If another instrument is the reference, record its optical method, range and uncertainty. Different particle populations or methods can produce differences; do not force every process sample to match with one arbitrary multiplier.

Conductivity or salinity can be useful companion measurements, but neither substitutes for turbidity. A salt solution can change ionic conductivity without providing a valid turbidity calibration point. Keep the standard solutions and calibration commands assigned to the correct parameter.

Test the application after the sensor swap

Verify a fresh value, a disconnected probe, an out-of-range or invalid response and a power restart. The application should identify missing data rather than silently displaying the last NTU as current. Set the required recovery behavior before unattended operation; these are host-software functions, not automatic consequences of buying an industrial probe.

Recheck alarms after changing the range or averaging interval. A threshold inherited from the old module may no longer correspond to the same water condition. For quotation, send the existing input path, board interface, expected NTU range, water type, cable length and any reference results. NiuBoL can then review the probe configuration without treating a prototype as an accepted monitoring system.

Additional BOD, pH or oxygen channels require their own methods and maintenance. Their inclusion in a multiparameter station does not make turbidity a measurement of dissolved organics, pathogens or overall water safety.

DDM-206-S salinity probe that cannot calibrate an optical turbidity channel

Project Decision FAQ

Q1. Can the old voltage-to-NTU equation be reused?

No, not on the new probe's calibrated digital NTU output. Identify which conversions were specific to the analog module and replace them with the selected instrument's documented decoding.

Q2. Can RS485 wires connect directly to board serial pins?

No. Use a compatible physical RS485 interface with correct logic levels and field protection. The probe also needs its specified supply; serial pins do not provide that supply.

Q3. Does 0.01 NTU resolution guarantee a 0.01 NTU detection limit?

No. Resolution is the output increment. Establish usable low-level performance from the range-specific accuracy criterion, reference uncertainty and actual optical installation.

Q4. Can both probes be compared in a small drinking glass?

Not if the container violates their optical clearances. The NBL-WQ-TS needs more than 5 cm to side walls and more than 10 cm to the bottom. Use a suitable vessel and representative, stable sample conditions.

Q5. Is replacing the probe enough for unattended deployment?

No. Verify stale-data handling, restart behavior, alarms, enclosure, power and safe cleaning access. Approval should cover the complete deployed measurement path, including the receiving software.

BOD-4S optical BOD instrument for a separate water quality parameter

Summary

An industrial replacement for an Arduino water turbidity sensor requires a new, verified measurement path. Select the optical range, use the correct electrical interface, remove obsolete conversion code and test around the operating threshold. Preserve useful application functions, but revalidate them against the actual NiuBoL probe and installation.

Related recommendations

Sensors & Weather Stations Catalog

Agriculture Sensors and Weather Stations Catalog-NiuBoL.pdf

Weather Stations Catalog-NiuBoL.pdf

Agriculture Sensors Catalog-NiuBoL.pdf

Water Quality Sensor Catalog-NiuBoL.pdf

Related products

Tell us your requirements, Let's discuss more about your project.we can do more.

Name*

Tel*

Email*

Company*

Country*

Message


online
Contacts
Email
Top
XArduino Water Turbidity Sensor: Replace an Analog Module with RS485-Product knowledge-Automatic Weather Stations_Industrial, Agricultural, Water & Environmental IoT Monitoring Solutions—NiuBoL

Screenshot, WhatsApp to identify the QR code

WhatsApp number:+8615367865107

(Click on WhatsApp to copy and add friends)

Open WhatsApp

The WhatsApp ID has been copied, please open WhatsApp to add consultation details!
WhatsApp